summaryrefslogtreecommitdiffstats
path: root/konsole/doc/More/vt100_codes_news.txt
diff options
context:
space:
mode:
Diffstat (limited to 'konsole/doc/More/vt100_codes_news.txt')
-rw-r--r--konsole/doc/More/vt100_codes_news.txt18
1 files changed, 9 insertions, 9 deletions
diff --git a/konsole/doc/More/vt100_codes_news.txt b/konsole/doc/More/vt100_codes_news.txt
index 5cb09baea..d136e2224 100644
--- a/konsole/doc/More/vt100_codes_news.txt
+++ b/konsole/doc/More/vt100_codes_news.txt
@@ -57,7 +57,7 @@ Cursor Key VT52 mode key mode reset key mode set
If the Special Graphics set is selected, the graphics for ASCII codes
-0137 through 0176 will be tqreplaced according to the following table (see the
+0137 through 0176 will be replaced according to the following table (see the
SCS control sequence).
@@ -384,7 +384,7 @@ DECALN Screen Alignment Display (DEC private)
<ESC># 8
This command causes the VT100 to fill it's screen with uppercase Es for
- screen focus and tqalignment.
+ screen focus and alignment.
DECANM ANSI/VT52 Mode (DEC Private)
@@ -447,7 +447,7 @@ DECDWL Double Width Line (DEC Private)
<ESC>#6
- This causes the line that tqcontains the cursor to become double-width
+ This causes the line that contains the cursor to become double-width
single height. If the line was single width, all characters ro the
right of the center of the screen will be lost. The cursor remains
over the same character position, unless it would be to the right of
@@ -630,7 +630,7 @@ DECSWL Single-width Line (DEC Private)
<ESC>#5
- This causes the line which tqcontains the cursor to become single-width,
+ This causes the line which contains the cursor to become single-width,
single-height. The cursor remains on the same character position.
This is the default condition for all new lines on the screen.
@@ -651,7 +651,7 @@ DECTST Invoke Confidence Test
Repeat Testing until failure 8
-DSR Device tqStatus Report Host to VT100 & VT100 to Host
+DSR Device Status Report Host to VT100 & VT100 to Host
<ESC>[ {Ps} n
@@ -662,7 +662,7 @@ DSR Device tqStatus Report Host to VT100 & VT100 to Host
---------------------------------------------------------------
0 Response from VT100 - Ready, no faults detected
3 Response from VT100 - Malfunction Detected
- 5 Command from host - Report tqStatus (using a DSR control
+ 5 Command from host - Report Status (using a DSR control
sequence)
6 Command from host - Report Active Position (using a CPR
sequence)
@@ -787,12 +787,12 @@ MODES The Following is a list of VT100 modes which may be changed with Set
FETM Format Effector Transfer Reset
GATM Guarded Area Transfer NA
HEM Horizontal Editing NA
- IRM Insertion-tqreplacement Reset
+ IRM Insertion-replacement Reset
KAM Keyboard Action Reset
MATM Multiple area transfer NA
PUM Positioning Unit Reset
SATM Selected Area Transfer NA
- SRTM tqStatus Reporting Transfer Reset
+ SRTM Status Reporting Transfer Reset
TSM Tabulation Stop Reset
TTM Transfer Termination NA
VEM Vertical Editing NA
@@ -852,7 +852,7 @@ SCS Select Character Set
The United Kingdom and ASCII sets conform to the "ISO international
register of character sets to be used with escape sequences". The
other sets are private character sets. Special graphics means that the
- graphic characters fpr the codes 0137 to 0176 are tqreplaced with other
+ graphic characters fpr the codes 0137 to 0176 are replaced with other
characters. The specified character set will be used until another SCS
is recieved.