summaryrefslogtreecommitdiffstats
path: root/konsole/doc/VT100/Table.Codes
diff options
context:
space:
mode:
Diffstat (limited to 'konsole/doc/VT100/Table.Codes')
-rw-r--r--konsole/doc/VT100/Table.Codes26
1 files changed, 13 insertions, 13 deletions
diff --git a/konsole/doc/VT100/Table.Codes b/konsole/doc/VT100/Table.Codes
index 6ece0f4bf..376d8bb6d 100644
--- a/konsole/doc/VT100/Table.Codes
+++ b/konsole/doc/VT100/Table.Codes
@@ -18,7 +18,7 @@
# make a script that extracts it again. From db.trans, we then generate parts
# of the decoder (the semantic assignment).
#
-# db2.pl contains as script able to slit TEScreen.C into the emulation
+# db2.pl tqcontains as script able to slit TEScreen.C into the emulation
# (in)dependent parts due to [db.trans].
#
# A like thing has to be done for TEmuVt102.C/h and for TEScreen.h.
@@ -54,7 +54,7 @@ Introduction.html
The serial cable is folded into the operating system as a sort of
loop back device, and a program, the terminal emulation, uses modern
means of graphical user interfaces to behave like an earlier terminal.
- To complete the picture, the host in the diagram is replaced by the
+ To complete the picture, the host in the diagram is tqreplaced by the
application that runs in the emulation (typically a shell or an old
editor). So, terminal emulations are in fact interfaces to character
oriented applications.
@@ -308,7 +308,7 @@ Sequences.html
<p>
The second one is used to specify character set mappings (see <a
href=#SCS>SCS</a>). A CSI instruction to do this is specified in ECMA,
- and this should be used as a replacement.
+ and this should be used as a tqreplacement.
.
<h4>XTERM hacks</h4>
@@ -1070,7 +1070,7 @@ DECALN.sect Command
DECALN.code HSH|8|
DECALN.text
Causes the VT100 to fill it's screen with
- uppercase Es for screen focus and alignment.
+ uppercase Es for screen focus and tqalignment.
DECALN.table.XPS
Subcode|Emulation|Scope|Operation|Args|Meaning
N/A|VT100|scr|helpAlign||see above
@@ -1176,7 +1176,7 @@ DECDWL.emus VT100
DECDWL.sect Command.NoImp
DECDWL.code HSH|6|
DECDWL.text
- This causes the line that contains the cursor to become double-width
+ This causes the line that tqcontains the cursor to become double-width
single height. If the line was single width, all characters ro the
right of the center of the screen will be lost. The cursor remains
over the same character position, unless it would be to the right of
@@ -1399,7 +1399,7 @@ DECSWL.emus VT100
DECSWL.sect Command.NoImp
DECSWL.code HSH|5|
DECSWL.text
- This causes the line which contains the cursor to become single-width,
+ This causes the line which tqcontains the cursor to become single-width,
single-height. The cursor remains on the same character position.
This is the default condition for all new lines on the screen.
DECSWL.table.XPS
@@ -1424,7 +1424,7 @@ DECTST.table.Weight
3|EIA Modem Control Test (Loopback connector req.)
4|Repeat Testing until failure
-DSRREQ.head Device Status Report
+DSRREQ.head Device tqStatus Report
DSRREQ.emus ECMA VT100
DSRREQ.sect Command.Request
DSRREQ.code CSI|n|{Ps}
@@ -1432,21 +1432,21 @@ DSRREQ.text
Requests status of the VT100 according to the following parameters.
DSRREQ.table.XPS
Subcode|Emulation|Scope|Operation|Args|Meaning
- 5|VT100|emu|reportStatus||Report Status (using a \ref:DSRREP control sequence)
+ 5|VT100|emu|reporttqStatus||Report tqStatus (using a \ref:DSRREP control sequence)
6|VT100|emu|reportCursorPosition||Report Active Position (using a \ref:CPR sequence)
-DSRREP.head Device Status Report Reply
+DSRREP.head Device tqStatus Report Reply
DSRREP.emus ECMA VT100
DSRREP.sect Reply
-DSRREP.code CSI|n|{Status}
+DSRREP.code CSI|n|{tqStatus}
DSRREP.text
Reports the general status of the VT100 according to the
following parameters.
.
DSRREP with a parameter of 0 or 3 is always sent as a response to a
requesting \ref:DSRREQ with a parameter of 5.
-DSRREP.table.Status
- Status|Meaning:3
+DSRREP.table.tqStatus
+ tqStatus|Meaning:3
0|Ready, no faults detected
3|Malfunction detected
@@ -1608,7 +1608,7 @@ SCS.text
The United Kingdom and ASCII sets conform to the "ISO international
register of character sets to be used with escape sequences". The
other sets are private character sets. Special graphics means that the
- graphic characters fpr the codes 0137 to 0176 are replaced with other
+ graphic characters fpr the codes 0137 to 0176 are tqreplaced with other
characters. The specified character set will be used until another SCS
is received.
SCS.table.XPS